ToolSphere
All perfboard layouts

555 Monostable Delay Perfboard Layout

A brief button press triggers a nominal 1.1-second LED pulse. The board is schematic-verified with the simulator’s connection checker, not physically prototype-tested.

NE555 monostable LED delay perfboard layoutJ1 5VJ2 TRIGGER BUTTONU1 NE555R1 100kR2 10kR3 1kD1 LEDC1 10uC2 10nC3 100n
Open this layout in the simulator Connection check: no shorts, 7 named nets

Red wires carry power, white is ground, yellow and blue are signals. Every hole is an isolated pad; connections are the wires shown. In the simulator you can move parts, add your own and re-run the check.

Parts list

As an Amazon Associate, ToolSphere earns from qualifying purchases.

How it works

The regulated supply is 5 V. R1 is 100 kΩ and C1 is 10 µF. The 555 calculator uses t = 1.1 R C in monostable mode; running that exact formula gives 1.1 seconds for these parts. This is a nominal interval, affected by capacitor tolerance, leakage and the actual timer, not a precision stopwatch.

THRESHOLD and DISCHARGE share the timing node. R1 charges C1 from the supply while the output is high; C1’s negative leg returns to ground. A short low pulse on TRIGGER starts the interval. The 10 kΩ trigger pullup keeps the input high when the normally open external button is released. Do not join trigger to the timing node as in the astable circuit.

Press and release the button promptly, before the intended pulse ends. Holding trigger low can keep the output active beyond the nominal interval. This circuit is not debounced and does not guarantee a defined power-up pulse state. RESET is tied high; use a deliberately designed reset/power-on network if your application requires one. Follow the NE555 datasheet’s monostable connection and trigger guidance.

The output drives the LED through 1 kΩ. With an ideal 5 V output and an assumed 2 V red LED drop, the resistor library computes 3 mA. A bipolar NE555 does not reach the positive rail under load, so the real LED current will be lower and depends on the device. The current calculation is a stated ideal-output estimate, not a measured brightness claim.

C2 bypasses the control pin to ground and C3 bypasses the supply near the IC. Build on isolated pads with insulated jumpers; no stripboard cuts are needed. Continuous copper strips at these coordinates would require a different connection plan. Check unpowered continuity and electrolytic polarity before applying power.

Building it, step by step

  1. Fit the DIP socket and identify pin 1 from its notch. Wire GND, +5V, RESET high and the supply bypass.
  2. Join THRESHOLD and DISCHARGE to the timing node, then fit the 100 kΩ resistor to +5V and the 10 µF capacitor to ground with correct polarity.
  3. Wire the trigger pullup and the external normally open button between TRIGGER and GND. Leave the button released for the idle state.
  4. Fit the control bypass and output LED resistor, with the LED cathode grounded. Check every intended net unpowered.
  5. Apply the stated supply, briefly press and release the button, and compare the visible interval with the nominal RC estimate. Do not infer a repetition frequency from a one-shot pulse.

Tools for this build

Frequently asked questions

How long does the LED stay on?

The nominal RC calculation gives 1.1 seconds with 100 kΩ and 10 µF. Actual time depends on tolerances and trigger behavior; it has not been measured on a physical prototype.

Why does holding the button change the delay?

The 555 expects a trigger that returns high before the interval ends. A held-low trigger can prevent the expected end of the output pulse.

Can I use the astable wiring instead?

No. This one-shot keeps TRIGGER separate from the timing node. In the standard astable, trigger and threshold are joined and the circuit repeats.

Is this stripboard?

No. The layout uses isolated-pad perfboard and insulated jumpers, with no cuts. A stripboard adaptation needs its own cuts and connection check.