Perfboard & stripboard layouts
Common circuits laid out hole by hole, the way you would solder them. Each one has a parts list, the maths behind the part values, build steps, and a link that opens it in the perfboard simulator, where it passes the connection check with no shorts.
LED + resistor
A 5 V LED with its current-limiting resistor laid out on perfboard: the layout, parts list, the resistor maths and how to check it before soldering.
Voltage divider
Two resistors that scale a voltage down, laid out on perfboard with the output tapped off: layout, parts, the divider formula and when it works.
Pull-up + button
A push button with a 10 kΩ pull-up resistor on perfboard: the layout, why the pull-up is needed, the current it draws and how to read it in code.
Transistor switch
A 2N2222 switching a 12 V load from a 3.3 V GPIO, laid out on perfboard: layout, base resistor maths, parts, and when to use a MOSFET instead.
Stripboard LED (cuts)
The LED and resistor circuit on stripboard (Veroboard): which strips carry which net, where the two track cuts go and why, and how to check them.
NE555 astable
A 555 timer oscillator on perfboard: the layout with the RA/RB/C timing network, the frequency and duty-cycle maths, parts list and common faults.
7805 5 V supply
A 7805 5 V power supply on perfboard: input and output capacitors from the datasheet, a power LED, the layout, parts list and how much heat it makes.
Arduino Nano project
An Arduino Nano on perfboard with two LEDs on PWM pins, a button on D2 and an I2C header on A4/A5: the full layout, parts list and pin choices.
Relay driver
Switch a 5 V relay from a 3.3 V microcontroller pin with an NPN transistor and a flyback diode: the perfboard layout, base resistor maths and parts.
LM317 3.3 V supply
An LM317 adjustable regulator set to 3.3 V with 240 Ω and 390 Ω on perfboard: the layout, the output-voltage formula, parts and how to pick other voltages.
LDR light sensor
An LDR and 10 kΩ divider read by an Arduino analog pin, laid out on perfboard: the layout, the voltages in dark and bright light, the parts and the code.
RC low-pass filter
A first-order RC low-pass filter on perfboard with 1.6 kΩ and 100 nF (cutoff 995 Hz): the layout, the cutoff maths, parts and what the filter does.
MOSFET LED strip driver
Switch or dim a 12 V LED strip from an Arduino pin with a logic-level IRLZ44N MOSFET: the perfboard layout, gate resistors, heat and parts list.
Potentiometer input
Wire a 10 kΩ potentiometer to an Arduino analog input on perfboard: which pin goes where, the voltage at the wiper, the code and common mistakes.
PC817 optocoupler input
Read a 12 V signal safely with a 3.3 V microcontroller through a PC817 optocoupler: the isolated perfboard layout, resistor maths and parts list.
LM386 audio amplifier
The LM386 speaker amplifier on perfboard in its datasheet gain-of-20 form: volume pot, output and Zobel network, layout, parts and how to raise the gain.
L293D H-bridge + Nano
A Nano-controlled L293D H-bridge on isolated-pad perfboard: separate motor power, enable pulldown, decoupling and a verified pin-to-pin layout.
Two-transistor LED flasher
An alternating LED flasher with two 2N3904 transistors, cross-coupled capacitors and computed resistor currents on isolated-pad perfboard.
NE555 + CD4017 LED chaser
A 555-clocked ten-LED CD4017 chaser on perfboard, with one resistor per LED, a reset button connection and a verified pin-to-pin board.
555 PWM + MOSFET motor control
A limited-duty 555 PWM motor controller with a logic-level MOSFET, flyback diode and external potentiometer connection, on isolated-pad perfboard.
Arduino NPN piezo driver
A passive piezo driver from an Arduino GPIO: 2N3904 switch, computed base resistor, feed current limiting and a discharge path on perfboard.
NE555 monostable LED delay
A push-button NE555 one-shot on isolated perfboard: computed 1.1-second LED pulse, trigger pullup, timing capacitor and checked connections.
LM358 dark-activated LED
A 5 V LM358 dark sensor with an LDR divider, fixed reference and NPN LED driver: computed voltages, checked perfboard nets and parts list.
Conductivity water-level tone alarm
A low-voltage water probe alarm with NPN sensing, a 555 tone oscillator, LED and passive piezo driver: calculated values and checked perfboard nets.
Nano + L293D two-motor driver
Drive two DC motors with a classic Arduino Nano and L293D: checked perfboard wiring, separate power inputs, parts list and build steps.
ESP32 + 3.3 V regulator, LEDs and button
A specific 38-pin ESP32-DevKitC V4 with an external 3.3 V regulator, two LEDs and a button: checked perfboard nets, parts and build steps.
Nano + HC-SR04 and piezo buzzer
Wire a classic Arduino Nano to an HC-SR04 and passive piezo: checked perfboard nets, pin assignments, parts list and a short build guide.