ToolSphere

PerfBoard & Stripboard Simulator

Electronics

Plan and design perfboard and stripboard (veroboard) layouts online: real track cuts, a live short-circuit check, a parts list and share links. Free.

Tap two holes to join them. Tap the last hole again to stop wiring.

Loading the board…
Wires: 18Parts: 5

On this browser only

Give feedback

Did this tool help?

Tell us what worked, what didn’t, or what you’d like next.

Opens Google Forms in a new tab with this tool’s name filled in. No sign-in or email required. Feedback is optional.

Coming from Fritzing? See what carries over and what Fritzing still does better →

Try next

How to use PerfBoard & Stripboard Simulator

  1. 1Choose Perfboard or Stripboard above the canvas, then pick a starter circuit or start from the default board.
  2. 2Add standard parts in one click from the parts bar — resistors, LEDs, capacitors, TO-92 and TO-220 packages, DIP ICs, headers and an Arduino Nano — then drag them into place in Move mode.
  3. 3On stripboard, switch to Cut mode and click a hole to drill out the copper and split the strip; click again to undo the cut.
  4. 4Route wire links in Wire mode and right-click a wire to give it a net label such as GND or +5V.
  5. 5Watch the connection check: it flags shorts between labelled nets, parts bridged by an uncut strip, and pins connected to nothing, as you edit.
  6. 6Share copies a link containing the whole layout; Save writes a .json project and Export writes a PNG.

About PerfBoard & Stripboard Simulator

Perfboard & Stripboard Layout Planner

Plan where every component and link goes before you heat the iron. The board, the
components and the wiring all live in your browser — nothing is uploaded, and the
layout survives a reload.

Start from one of the example circuits above the canvas if you want to see how a
finished layout is put together, or clear the board and lay out your own.

Perfboard, stripboard or breadboard

These solve different stages of the same problem, and picking the wrong one costs
an evening.

Breadboard is for deciding whether a circuit works at all. Nothing is soldered,
so everything is reversible — and nothing is reliable. Contact resistance drifts,
long jumpers pick up noise, and anything above a few megahertz misbehaves for
reasons that have nothing to do with your design. Prototype here, do not ship here.

Perfboard gives every hole its own isolated pad. You solder the parts down and
then make every single connection yourself, usually with wire on the underside.
That is more work than stripboard, and in exchange the layout is entirely yours:
no track to cut, no accidental connection to discover later.

Stripboard (Veroboard) runs copper tracks along whole rows. Parts sharing a row
are connected the moment they are soldered, which does most of the wiring for you —
and means the real design work is deciding where to cut the tracks. Miss a cut and
you have a short you will spend an hour finding.

Both are modelled here. Switch the board to Stripboard and every row becomes one
continuous strip of copper; Cut mode drills out the copper at a hole and splits
the strip there, exactly as a spot-face cutter does on a real board.

Laying out a board that is buildable

A layout can be electrically correct and still be miserable to solder.

Put the rails at the edges. Power along one side, ground along the other, and
every part reaches a rail with a short run. The example circuits all do this because
it is what makes a board readable a month later.

Keep grounds together rather than chaining them. A ground that wanders through
five components in series shares the current of all five, and the voltage drop shows
up as noise in whichever one is most sensitive.

Leave a hole of clearance around tall parts. Electrolytics, TO-220 tabs and
connectors need space your schematic does not show. Placing them first, before the
small passives, saves a rework.

Decide the component order before you solder. Low parts first, then taller ones:
once a big capacitor is in, the resistors behind it are hard to reach.

The connection check

As you edit, the board is turned into nets — groups of holes that are electrically
one — and checked for the mistakes that cost an evening with a multimeter:

Shorts between named nets. Label a wire GND and another +5V; if copper or links
ever join them, it is reported as a short circuit before you power anything.

Parts bridged by a strip. A resistor lying along one strip with no cut between its
legs is shorted out, and a DIP IC dropped across uncut strips joins pin 1 to pin 8, 2 to
7 and so on. This is the single most common stripboard mistake, and it is flagged by pin.

Wires on drilled-out holes, and pins going nowhere. A link soldered into a cut hole
connects to nothing on the strip, and a leg with nothing else on its copper is usually a
missing wire.

Ready-made example circuits

Six classic circuits load from the example chips above the board, each laid out the way you would solder it:

  • LED + resistor: a current-limiting resistor in series with an LED between the +5 V and ground rails. Work out the resistor with the LED resistor calculator first.
  • Voltage divider: two equal resistors halving the input, with the midpoint tapped off. The voltage divider calculator gives other ratios.
  • Pull-up + button: a 10 kΩ resistor holding an input high and a push button pulling it to ground, the standard way to read a switch on an Arduino or ESP32.
  • Transistor switch: an NPN transistor switching a 12 V load from a 3.3 V GPIO, with a base resistor limiting the drive current.
  • Stripboard LED (cuts): the LED circuit again on stripboard. Each part lies along a copper strip, so a track cut between its legs is what stops it being shorted out; the connection check flags it if you forget one.
  • NE555 astable: the classic square-wave oscillator. The 8-pin chip straddles the board with the RA, RB and C timing network alongside; the frequency is f = 1.44 / ((RA + 2·RB)·C), which the 555 timer calculator works out for you.

Load one, move parts around and watch the connection check update. It is the quickest way to learn how a layout on a grid of holes maps onto a schematic.

Layout library

For common circuits there is no need to start from scratch: the perfboard layout library has checked, ready-to-solder layouts for a 7805 5 V supply, an NE555 astable, an Arduino Nano with LEDs, a button and I2C, an NPN transistor switch and more. Each page has the parts list, the maths behind the values and a link that opens the layout here.

What this tool does not do

It checks connectivity, not the circuit. It does not simulate voltages or currents,
will not tell you a resistor is the wrong value, and does not check whether a part can
dissipate the power you are asking of it. Work the values out first, with the
calculators linked below, then use this to decide where the parts go and to confirm the
copper joins exactly what you meant it to.

For a board you intend to manufacture rather than hand-build, this is the wrong
tool entirely: use KiCad or EasyEDA, which produce Gerbers.

Sharing a layout

Share puts the whole board inside the link itself, because the site has no server to
store it on. Anyone opening that link sees your exact layout — useful for a forum
post, a build guide, or asking someone why your circuit does not work. Very large
boards outgrow what a URL can carry; those save as a .json project file instead.

Planning the whole project? The electronics lab puts the calculators for values, parts and board layout in the order you need them. Coming from Fritzing? See how this compares with Fritzing.

Guides and tutorials

Frequently asked questions

What is the difference between Perfboard and Stripboard?

Perfboard (perforated board) features isolated copper pads for every single hole, requiring manual wire routing between points. Stripboard (VeroBoard) features parallel copper tracks connecting entire rows or columns of holes, requiring track cuts to break connections.

Can I export my board layout to Gerber files?

This simulator is optimized for prototyping layouts, netlist planning, and PNG/JSON exports. For production PCB manufacturing (Gerber generation), we recommend exporting your netlist layout to software like KiCad or EasyEDA.

Does the simulator run offline?

Yes! ToolSphere is 100% offline-first. Once the page is loaded, the simulator engine operates completely within your browser without needing an active internet connection.

Where do I start if I have never used this?

Click one of the starter circuits above the canvas — LED + resistor is the simplest. It loads a complete, labelled layout you can pull apart to see how components, pins and net labels fit together. Undo restores whatever was there before.

Can I send my layout to someone else?

Yes. Share copies a link with the entire board encoded inside it, so there is nothing stored on a server and no account involved. Opening that link anywhere reproduces the layout exactly. For a board too large to fit in a URL, save the .json project and send the file.

Is my work saved if I close the tab?

Yes — each board is kept in your browser's local storage and comes back when you return, on that browser and device only. It is not synced anywhere. Save the .json project for anything you would be upset to lose.

Does it check my circuit for mistakes?

It checks the copper, not the circuit. The connection check catches shorts between labelled nets, parts bridged by an uncut strip, wires on drilled-out holes and pins connected to nothing. It does not simulate voltages or currents or tell you a value is wrong — work those out first with the Ohm's law, LED resistor and voltage divider calculators linked below, then lay the board out here.

How do I plan a stripboard build with a perfboard tool?

Draw the connections you want as wires. On stripboard the whole row is already connected, so every row carrying two different nets is a row needing a track cut between them. Reading your finished layout that way gives you the cut list.

How do track cuts work in the stripboard designer?

Switch the board to Stripboard, choose Cut mode, and click a hole. The copper at that hole is drilled away, splitting the strip into two separate pieces, and the hole is marked with a red cross. Click the same hole again to remove the cut. The connection check updates immediately, so you can see a short disappear as you cut.

Can it find short circuits in my layout?

Yes, at the copper level. Every time you edit, it works out which holes are electrically joined and flags two differently labelled nets that touch (such as +5V and GND), parts whose legs are bridged by an uncut strip, and pins connected to nothing. It does not simulate the circuit's behavior, only whether the copper joins what you intended.

Why does a DIP IC on stripboard show four warnings?

Because an IC straddling uncut strips has each pin on the left joined to the pin opposite it on the right — pin 1 to pin 8, 2 to 7, and so on. The fix on a real board is one cut per row between the two columns of pins, usually directly under the chip. Make those cuts and the warnings clear.

What parts are in the parts library?

Axial resistors and diodes at 0.4-inch spacing, LEDs, ceramic and electrolytic capacitors, TO-92 transistors, TO-220 regulators, DIP-8 and DIP-14 ICs, 2- and 4-pin headers, and an Arduino Nano with every pin named (D0–D13, A0–A7, 5V, GND, VIN), all on the standard 0.1-inch grid. Each lands in the first free spot with its legs in the right holes and a reference designator such as R1 or U2.

Have a suggestion for PerfBoard & Stripboard Simulator?Share your feedback ↗