ToolSphere
All perfboard layouts

555 and CD4017 LED Chaser Perfboard Layout

The NE555 generates clock pulses and a CD4017B advances one decoded output at a time. This example uses a 9 V supply and low-current LED loads.

NE555 + CD4017 LED chaser perfboard layoutJ1 9VU1 NE555U2 CD4017BR1 10kR2 47kR13 10kC1 1uC2 10nC3 100nC4 100nJ2 RESET BUTTONR3 10kD1 LEDR4 10kD2 LEDR5 10kD3 LEDR6 10kD4 LEDR7 10kD5 LEDR8 10kD6 LEDR9 10kD7 LEDR10 10kD8 LEDR11 10kD9 LEDR12 10kD10 LED
Open this layout in the simulator Connection check: no shorts, 27 named nets

Red wires carry power, white is ground, yellow and blue are signals. Every hole is an isolated pad; connections are the wires shown. In the simulator you can move parts, add your own and re-run the check.

Parts list

As an Amazon Associate, ToolSphere earns from qualifying purchases.

How it works

The timer has RA = 10 kΩ, RB = 47 kΩ and C = 1 µF. Running the timer tool's exact ln(2) equations gives 13.87 Hz, so a complete ten-output sequence takes approximately 0.721 s. These are nominal RC timings; capacitor tolerance and actual chip thresholds affect the rate.

The counter's output pin order is not consecutive: Q0 through Q9 use pins 3, 2, 4, 7, 10, 1, 5, 6, 9 and 11. The layout connects each to its own 10 kΩ resistor and red LED. With a hypothetical 2 V LED and an ideal 9 V high, the resistance library gives 0.7 mA; actual output voltage falls under load, so treat this as a simple upper estimate. Use efficient low-current LEDs, not high-power LEDs.

Clock goes to the counter's CLOCK input and INHIBIT stays grounded. RESET has a 10 kΩ pulldown; the external momentary button connects it to +9V. Press reset to select Q0 rather than assuming a deterministic power-up state. The carry output is intentionally unused.

C3 and C4 are supply bypass capacitors, while C2 bypasses the timer control pin. Verify the CD4017B pinout and operating limits and the NE555 datasheet. This 9 V example is not a promise of direct logic compatibility after changing supplies or chip families; check the clock high/low levels against the counter's requirements.

All pads are isolated. Use insulated underside jumpers between the named junctions; wire crossings without endpoints are not joints. No stripboard cuts are present or implied.

Building it, step by step

  1. Fit both IC sockets using the package pin numbering. Wire every supply/ground connection and the local bypass capacitors first.
  2. Wire the NE555 RA/RB/capacitor network, join trigger to threshold and tie timer reset high.
  3. Connect the timer output to counter clock, ground inhibit, and wire the reset pulldown and external momentary button.
  4. Follow Q0–Q9 by their pin labels, fitting a separate resistor and correctly oriented LED for each output.
  5. Check unpowered continuity and polarity. Apply the stated supply, press counter reset and verify that the light advances before changing timing parts.

Tools for this build

Frequently asked questions

Why are the counter output pins not in numerical order?

The package routes decoded outputs to the numbered pins shown in its datasheet. Follow Q0–Q9 labels and the board connections, not an assumed left-to-right sequence.

Why is there one resistor for every LED?

Each LED branch needs its own defined load. This example uses small currents and does not assume the CMOS counter can directly drive ordinary high-current or power LEDs.

How do I start with the first LED?

Use the reset button connection to assert RESET, then release it. The layout does not assume the counter always powers up in Q0 without reset.

Can I change the speed?

Recompute the 555 timing values and change its resistors or capacitor. Check logic voltage compatibility and component ratings if also changing the supply or IC family.