ToolSphere

Propeller Thrust Calculator

Robotics

Estimate static propeller thrust from shaft power, diameter and figure of merit, then compare total thrust with vehicle weight. No throttle prediction.

Enter shaft power and propeller diameter, then add the motor count and total weight to compare hover requirements.

Estimated thrust per motor

1022 g

A static disc-model estimate from shaft watts; verify with measurements for your motor and propeller.

Total thrust
4086 g
4 motors
Efficiency
6.8 g/W
Based on entered shaft power, not battery watts
Thrust-to-weight 3.41:1; hover requires 29.4% of estimated maximum thrust, not a throttle command. Meets the 2:1 planning reference; actual control margin needs separate evaluation.

This is momentum theory: thrust is derived from how much air the disc can accelerate, corrected by a figure of merit for how well a real blade does it. It models the disc, not your blade geometry, so treat it as a sizing estimate and trust a thrust-stand measurement over it.

On this browser only

Give feedback

Did this tool help?

Tell us what worked, what didn’t, or what you’d like next.

Opens Google Forms in a new tab with this tool’s name filled in. No sign-in or email required. Feedback is optional.

How to use Propeller Thrust Calculator

  1. 1Enter mechanical shaft power per motor in watts, rather than battery input power or the sum for every motor.
  2. 2Enter propeller diameter in inches and figure of merit as a percentage above zero and no greater than 100.
  3. 3Enter a whole positive motor count and the complete all-up vehicle mass in grams.
  4. 4Read estimated thrust per motor, total thrust and grams-force per shaft watt, then compare thrust-to-weight and the required thrust fraction.
  5. 5Use propeller-specific performance data and measured thrust/current to evaluate the actual motor, propeller and power system. The result does not predict throttle command.

About Propeller Thrust Calculator

Estimate static thrust from shaft power

This propeller thrust calculator uses an actuator-disc momentum model to estimate static thrust from mechanical shaft power, propeller diameter and an assumed figure of merit. It also combines identical motor-propeller units to compare total thrust with all-up vehicle weight. Use it for a first numerical comparison when exploring disc size or available shaft power.

The estimate is for static conditions, rather than a propeller moving forward through the air. It is not a blade-design solver, a motor electrical model or a thrust-stand measurement. There are no pitch, RPM, blade-count or advance-speed inputs. Different real propellers can therefore give different results even when this simplified calculation receives the same diameter and power.

The implemented momentum-theory formula

The library calculates T = (FM × P × √(2ρA))^(2/3). T is thrust in newtons, P is shaft power in watts, FM is the figure of merit as a fraction, and A is the disc area in square meters. Diameter in inches is converted to meters using 0.0254 meters per inch, then A = π × diameter² / 4.

The interface fixes air density at 1.225 kg/m³. It does not expose altitude, ambient temperature or density controls, so the displayed result cannot directly represent a different atmospheric condition. The model relates ideal induced power to thrust; the figure of merit accounts approximately for the difference between the ideal disc and the actual rotor's shaft-power requirement.

Enter figure of merit as a percentage in the interface. The default 60 means a fraction of 0.6 inside the equation. Entering 0.6 into the percentage field would instead mean a much smaller fraction. This is not the motor's electrical efficiency and it does not convert battery watts into shaft watts.

Worked example using the default inputs

Use 150 W shaft power per motor, a 10-inch propeller, 60% figure of merit, four motors and 1200 g all-up mass. The tested library returns:

Quantity Model result
Disc area per propeller 0.05067075 m²
Thrust per motor 10.0185 N
Equivalent thrust per motor 1021.603 gram-force
Thrust per shaft watt 6.81069 gram-force/W
Total thrust divided by vehicle weight 3.40534:1
Required fraction of estimated maximum thrust 29.3656%

The interface rounds the individual thrust to 1022 g and the newton result to 10.02 N. The g label in propeller thrust results is customary shorthand for gram-force, while the all-up input is vehicle mass in grams. Comparing them assumes the same gravitational conversion, which the library handles consistently.

The required fraction means the estimated hover thrust divided by the entered maximum-power thrust estimate. It does not mean the controller should receive that percentage of its throttle command. Motor speed, ESC mapping and propeller thrust do not generally form a simple linear command-to-thrust relationship.

Compare power without assuming identical efficiency

Keeping the same diameter and figure of merit, 75 W gives 643.570 gram-force per motor, while 300 W gives 1621.694 gram-force. The corresponding thrust per shaft watt is 8.58093 and 5.40565. Increasing shaft power therefore increases thrust but does not make the thrust-per-watt number constant in this model.

This comparison does not show whether a particular motor can deliver either power continuously or whether the propeller can operate within its limits. Electrical current, motor temperature, ESC capability and mechanical speed limits are outside the inputs. Do not interpret a calculated power comparison as permission to change a physical setup without its component-specific information.

Diameter and figure of merit are assumptions

At the default power and figure of merit, changing diameter to 12 inches gives about 1153.638 gram-force per motor. The larger disc changes the mathematical estimate, but its real shaft-power demand also depends on geometry and operating speed. The tool does not find an RPM or pitch that will produce the entered power.

At the default diameter and power, a 40% figure of merit gives about 779.629 gram-force. Use this field to explore a known or defensible assumption, not to label an unknown propeller as good or bad. A single universal figure of merit cannot capture every blade design and operating point. The result is sensitive to the inputs even when all of them are syntactically valid.

Thrust-to-weight and impossible hover

The total estimate assumes each motor-propeller unit provides the same thrust independently. Total thrust-to-weight is motor count × per-motor thrust divided by all-up weight. All-up weight must include the battery, frame, electronics, motors, payload and other carried items, rather than only the advertised payload.

The required thrust fraction is allowed to exceed the available estimate. If calculated maximum thrust is below weight, the interface explicitly says this model cannot support hover instead of clipping the result to a reassuring percentage. A ratio above unity only establishes that particular mathematical comparison. It does not verify stable hover or adequate control reserve.

The tool also compares against a 2:1 planning reference. Meeting that reference is not a guarantee of handling in wind, recovery from a disturbance or operation after a motor problem. Airframe dynamics, rotor interactions, battery sag and control limits require separate evaluation. The calculator does not model ground effect or aerodynamic interference between rotors.

Compare with propeller-specific information

The APC performance-data resource provides propeller-specific information over operating conditions. Check how a source's data were produced and which propeller, RPM and conditions they describe. A measured thrust-stand result and a manufacturer prediction each need their own context; neither is reproduced automatically by this generic disc model.

The motor KV calculator provides a separate speed estimate, not a direct shaft-power measurement. Use the LiPo calculator to interpret pack energy and current labels, and the flight-time calculator for a separate capacity-and-current estimate. Keep shaft power, electrical input and actual flying performance distinct when comparing the results.

Guides and tutorials

Frequently asked questions

How does this calculate propeller thrust?

It uses shaft power, disc area, fixed air density and an assumed figure of merit in a momentum-theory equation. It does not resolve the actual blade geometry or measure the thrust of a specific propeller.

Should I enter battery watts or motor shaft watts?

Enter the mechanical power delivered at each motor shaft. Electrical input includes motor and controller losses, so it is not automatically the same value.

Is the figure of merit field a fraction or percentage?

The interface expects a percentage and converts it to a fraction for the formula. It is a rotor power-model assumption, separate from motor electrical efficiency.

Can I calculate thrust from pitch and RPM here?

No; this interface does not accept pitch or RPM. Use propeller-specific data or a suitable geometry-based model for that calculation.

Does the hover percentage tell me what throttle to command?

No; the result is the required fraction of estimated maximum thrust. A controller command needs the actual throttle-to-thrust relationship for the propulsion system.

What happens when the estimated thrust is below the vehicle weight?

The required fraction can exceed the available thrust and the interface says the model cannot support hover. It does not hide the deficit by clipping the displayed requirement.

Does meeting the planning thrust-to-weight reference guarantee good handling?

No; it is a numerical reference rather than a complete flight-performance check. Control reserve depends on the airframe, operating conditions and actual propulsion behavior.

Is grams per watt based on battery power?

No; this panel divides estimated gram-force by the shaft power you entered. Do not compare it directly with an electrical-input efficiency figure unless the definitions match.

Can I enter altitude or air temperature?

No; the interface uses a fixed air density. Atmospheric changes and rotor interactions are outside the displayed model.

Why can a manufacturer table disagree with this calculator?

A propeller-specific source can account for geometry and particular operating conditions that this generic disc model does not accept. Check the source method and conditions, and use measurements appropriate to the actual setup.

Have a suggestion for Propeller Thrust Calculator?Share your feedback ↗