ToolSphere
Back to all articles
robotics

Brushless Motor KV to RPM, Explained

2026-10-205 min read

Try it: free Motor KV to RPM Calculator

Estimate brushless motor RPM from KV and battery cells

Open →

KV on a brushless motor is not kilovolts. It's the motor's speed constant: RPM per volt with no load. A 920 KV motor spins about 920 RPM for every volt you give it, before anything is attached to the shaft.

From KV to RPM

no-load RPM = KV × battery voltage
battery voltage = cells × 3.7 V (nominal) or × 4.2 V (fully charged)

A propeller then pulls the motor down. A loaded speed of about 85% of no-load is a reasonable first estimate.

Motor Pack Nominal V No-load RPM Loaded (≈ 85%) Fully charged, no load
2450 KV (5" FPV) 4S 14.8 V 36,260 30,821 41,160
1750 KV (5" FPV) 6S 22.2 V 38,850 33,023 44,100
920 KV (10" camera quad) 4S 14.8 V 13,616 11,574 15,456
380 KV (15" heavy lift) 6S 22.2 V 8,436 7,171 9,576

Notice the two 5-inch setups: a 2450 KV on 4S and a 1750 KV on 6S end up at nearly the same speed. Pilots who move to 6S buy lower-KV motors for exactly that reason; the higher voltage then means less current for the same power.

Why high KV means small props

KV is also a statement about torque. The motor's torque constant is

Kt (N·m per amp) = 60 / (2π × KV) ≈ 9.55 / KV

So a 920 KV motor makes 0.0104 N·m per amp, and a 2450 KV motor just 0.0039, less than half. Low-KV motors have more turns of wire, more torque per amp and less speed: they swing big propellers slowly. High-KV motors spin small propellers fast.

The other limit is the propeller tip speed. At the loaded speeds above:

Setup Tip speed Fraction of the speed of sound
5" prop, 30,821 RPM 205 m/s 0.60
10" prop, 11,574 RPM 154 m/s 0.45
15" prop, 7,171 RPM 143 m/s 0.42

Put a 10-inch prop on a 2450 KV motor and the tips would try to go faster than sound, the current would be enormous, and the motor or ESC would burn out long before. Match KV to prop size: the bigger the prop, the lower the KV.

Choosing KV

  1. Pick the prop size first from the frame.
  2. Pick the cell count from the weight and power you need.
  3. Choose a KV that puts the loaded RPM where that prop is efficient, then check the current at full throttle against the ESC and battery ratings.

Rough starting points for multirotors: 5" on 4S, 2300–2600 KV; 5" on 6S, 1700–1950 KV; 10" on 4S, 700–1000 KV.

Common mistakes

  • Reading KV as power. A higher-KV motor isn't stronger; it trades torque for speed.
  • Using 4.2 V per cell for flight estimates. That's a fresh pack; the voltage sags to around 3.7 V under load and over the flight.
  • Expecting the no-load RPM in the air. The prop always pulls it down, more so for bigger or higher-pitch props.
  • Moving to more cells without lowering KV. RPM, current and heat all rise.

Try it

The motor KV to RPM calculator gives no-load, loaded and full-charge RPM from KV and cell count. Turn that into lift with the propeller thrust calculator, and into endurance with the drone flight time calculator or the flight time guide.

Looking for other tools?

Explore ToolSphere Homepage →