ToolSphere
Back to all articles
robotics

Drone Flight Time Calculation, Step by Step

2026-10-206 min read

Try it: free Drone Flight Time Calculator

Estimate hover time from battery capacity and current or weight

Open →

Flight time is battery capacity divided by current draw. The whole difficulty is knowing the current, and that comes from how heavy the drone is and how efficiently its motors and propellers turn watts into lift.

The formula

flight time (min) = usable capacity (Ah) ÷ average current (A) × 60
usable capacity   = rated capacity × 0.8

The 0.8 is deliberate. Draining a LiPo much below about 20% remaining shortens its life sharply and leaves nothing in reserve for landing, so plan on 80% of the label.

If you have measured the average current (from your ESC telemetry or a flight log), you are done. If you haven't built it yet, estimate the current from the weight.

Estimating hover current from weight

Propulsion systems are rated in grams of thrust per watt. Typical multirotors manage 6–10 g/W in hover; big, slow propellers sit at the top of the range, small fast FPV props at the bottom (4–5 g/W).

hover power (W)   = all-up weight (g) ÷ efficiency (g/W)
hover current (A) = hover power ÷ pack voltage
pack voltage      = cells × 3.7 V

Worked example: a 4S camera quad

A 700 g frame (motors, props, flight controller, camera) with a 4S 5000 mAh pack weighing about 500 g, and propellers that manage 8 g/W:

all-up weight = 700 + 500                = 1,200 g
hover power   = 1,200 ÷ 8                = 150 W
hover current = 150 ÷ (4 × 3.7) = 150 ÷ 14.8 = 10.14 A
usable        = 5,000 × 0.8              = 4,000 mAh = 4.0 Ah
flight time   = 4.0 ÷ 10.14 × 60         = 23.7 minutes

That's hover. Forward flight at moderate speed is often a little more efficient than hover, but climbing, wind and aggressive manoeuvres cut it. Expect 15–25% less in real flying.

Why a bigger battery isn't a free win

A bigger pack adds energy and weight, and the extra weight raises the current. Same 700 g frame, same 8 g/W, with typical 4S pack weights:

Pack Pack weight All-up weight Hover current Flight time
3,000 mAh 330 g 1,030 g 8.70 A 16.6 min
5,000 mAh 500 g 1,200 g 10.14 A 23.7 min
8,000 mAh 750 g 1,450 g 12.25 A 31.4 min
10,000 mAh 950 g 1,650 g 13.94 A 34.4 min
16,000 mAh 1,400 g 2,100 g 17.74 A 43.3 min

Going from 5,000 to 10,000 mAh doubles the capacity but adds only 45% flight time. Past a point the motors are working mostly to lift the battery, and the thrust-to-weight ratio drops until the drone feels sluggish. Check that the motors can still produce at least 2× the all-up weight in total thrust; with four motors making 1,100 g each, 4,400 g against 1,200 g is a comfortable 3.7:1, hovering at about 27% throttle.

Worked example: a 5-inch FPV quad

650 g all-up on a 6S 1300 mAh pack, at about 4.5 g/W:

hover power   = 650 ÷ 4.5        = 144 W
hover current = 144 ÷ 22.2       = 6.51 A
flight time   = 1.04 ÷ 6.51 × 60 = 9.6 minutes hovering

Nobody hovers an FPV quad, though. Freestyle flying averages something like 25 A, which gives 1.04 ÷ 25 × 60 = 2.5 minutes. This is why FPV estimates should use measured current, not hover maths.

Using energy to compare packs

Different cell counts make mAh misleading. Compare watt-hours instead: usable Ah × cells × 3.7 V. The 4S 5000 mAh pack above gives 4.0 × 14.8 = 59.2 Wh usable. A 6S 3300 mAh pack is a similar 58.6 Wh, even though its mAh figure is much smaller.

Common mistakes

  • Using 100% of the capacity. Your estimate will be 25% too long and your pack will age quickly.
  • Leaving the battery out of the weight. It's often 30–45% of the all-up weight.
  • Using peak current from the ESC rating instead of the average.
  • Using 4.2 V per cell. That's full charge; the average over a flight is closer to 3.7 V.

Try it

The drone flight time calculator does this from either measured current or all-up weight and efficiency, and reports usable capacity and watt-hours. To estimate the efficiency and thrust side, use the propeller thrust calculator and the motor KV to RPM calculator. For charging the pack afterwards, there's the LiPo charge calculator, and for choosing one, the LiPo buying guide.

Looking for other tools?

Explore ToolSphere Homepage →