Estimate drone endurance from capacity and current
This drone flight time calculator estimates endurance from a LiPo pack and an average electrical load. Use it while planning a multirotor build, comparing a payload change, or checking whether a telemetry-based current estimate agrees with the battery capacity you intend to use. It returns estimated minutes, average current, and usable energy. The loaded example already has an answer, and every result updates when you change an active input.
There are two calculation paths. Estimate from weight converts all-up weight and entered propulsion efficiency into hover power and current. I measured the current uses your average pack current directly. Neither path simulates a flight route, selects a motor, predicts a battery cutoff, or calculates aircraft weight from individual parts. For a drone weight calculation, weigh the assembled aircraft with its intended battery and payload, then enter that total.
The flight time and drone power formulas
Usable capacity in Ah = capacity in mAh × usable percentage ÷ 100 ÷ 1000. Flight time in minutes = usable capacity in Ah ÷ average current in A × 60. Keep the current unit straight: the field expects amps, while capacity is entered in milliamp-hours. A pack's capacity rating and its discharge-current rating describe different properties.
Estimated mode adds these relationships: nominal voltage = series-cell count × 3.7 V; hover power in W = all-up weight in grams ÷ propulsion efficiency in g/W; average current = hover power ÷ nominal voltage. Here propulsion efficiency must refer to battery electrical power for the whole aircraft. It is a thrust-per-power figure, not motor efficiency expressed as a percentage.
Usable energy in Wh = usable capacity in Ah × nominal voltage. The calculation uses conventional LiPo nominal cell voltage throughout; it does not model voltage sag or the changing voltage during discharge. A different chemistry needs its own voltage model and should not be represented by changing the series-cell count until the displayed number looks plausible.
Worked example using the loaded aircraft
The loaded example uses a 5000 mAh pack, four series cells, 1200 g all-up weight, 8 g/W propulsion efficiency, and 80% usable capacity. Running those values through the calculator's propulsion library gives:
| Quantity | Calculated result |
|---|---|
| Nominal pack voltage | 14.8 V |
| Estimated hover power | 150 W |
| Estimated pack current | 10.135135 A |
| Usable capacity | 4000 mAh |
| Usable energy | 59.2 Wh |
| Estimated endurance | 23.68 minutes |
The headline rounds this to 23.7 min, and the supporting figures round current and energy for display. Those display choices do not change the underlying calculation. The energy label describes the planned usable portion of the pack, not energy already measured during an actual flight.
Now select measured current and enter 20 A, keeping the same battery and usable percentage. The result becomes 12.0 minutes. Reducing usable capacity to 70% gives 3500 mAh, 51.8 Wh, and 10.5 minutes. This comparison shows how strongly the answer depends on the entered load and reserve assumption; it does not establish which assumption fits your aircraft.
Read the result as a conditional estimate
The default 80% usable setting is an editable planning assumption. It does not measure state of charge, certify a landing reserve, or override pack and equipment instructions. Choose the usable portion from your operating procedure and observed battery behavior rather than treating the prefilled percentage as a universal discharge recommendation.
For measured mode, use average current at the battery over the activity you want to estimate. A single motor's current, a brief throttle peak, and an ESC's advertised current rating are not interchangeable with whole-pack average current. Logs that include the intended payload and flight style are more relevant than a measurement from a substantially different setup. This calculator does not import logs or average samples for you.
Compare payloads and battery changes carefully
Keeping the example battery and efficiency unchanged, increasing all-up weight to 1500 g gives about 12.668919 A and 18.944 minutes, displayed as 18.9 min. That comparison holds propulsion efficiency constant deliberately. A real configuration change can also change efficiency, so revise that input or switch to a measured average when you have suitable data.
A larger battery changes more than capacity. Include its mass in all-up weight and reconsider the current estimate. In measured mode, changing capacity alone scales endurance while preserving the entered current; the tool does not automatically account for the extra load of a heavier pack. It also does not optimize pack size or prove that a proposed combination can hover.
Common input mistakes and useful next checks
Do not enter a motor KV rating in the g/W field, use an individual cell's capacity multiplied by series count, or substitute peak motor current for average battery current. Use pack-label capacity and the actual series configuration. Blank or invalid active inputs clear the answer instead of retaining a previous flight time. Series-cell count must be a positive whole number, and usable capacity must be above zero and no more than the full pack.
Use the LiPo battery calculator for separate charge-rate and pack-energy arithmetic. Check lift estimates with the propeller thrust calculator, remembering that its efficiency output uses shaft watts, while this page's weight estimate needs battery watts. The motor KV to RPM calculator helps compare nominal speed assumptions. None of these estimates replaces measurements of the complete propulsion system.