ToolSphere
Back to all articles
robotics

How to Choose a LiPo Battery: S, mAh and C

2026-10-156 min read

Try it: free LiPo Battery Charge Rate Calculator

Work out LiPo currents, pack voltages and estimated charge time

Open →

A LiPo label like "3S 3300mAh 25C" holds three separate decisions. S (cells in series) sets the voltage, mAh sets how long it runs, and C sets how much current it can deliver. Choose them in that order: voltage from your electronics, capacity from the run time you need, and C rating from the peak current. Then check that the result isn't too heavy.

Step 1: cell count (S) from your motors and ESC

Each cell is 3.7 V nominal (4.2 V full), so 2S is 7.4 V, 3S 11.1 V, 4S 14.8 V and 6S 22.2 V. The ESC or motor driver's specification lists the cell counts it accepts ("2–4S"), and brushless motors are rated in kV (RPM per volt). More cells means more speed from the same motor but also more current and heat, so use what the motor and ESC are rated for, not the most they survive.

Step 2: capacity (mAh) from run time

capacity (Ah) = average current (A) × run time (h) ÷ 0.8

The ÷ 0.8 keeps 20% in reserve, because draining a LiPo flat shortens its life. Use average current, not peak: a car or drone spends most of its time well below full throttle. If you don't know it, log the current on one test run, or estimate about a third to half of the motors' combined maximum.

Step 3: C rating from peak current

minimum C rating = peak current (A) ÷ capacity (Ah)

Then add margin. Hobby C ratings are often optimistic, so many builders plan on about two-thirds of the label value.

Worked example

A 3S robot with two motors that each draw up to 20 A, averaging about 15 A in total while driving. The goal is 10 minutes of running.

  1. Voltage: the ESCs are rated 2–3S and the motors are specified at 11.1 V, so 3S.
  2. Capacity: 15 A × (10 ÷ 60) h ÷ 0.8 = 3.125 Ah, so choose the next common size up: 3300 mAh. At 15 A it gives about 10.6 minutes using 80% of the charge.
  3. C rating: peak current is 2 × 20 = 40 A, and 40 ÷ 3.3 = 12.1C minimum. A 25C pack is rated for 82.5 A continuous; even at two-thirds of its label (55 A) it covers the 40 A peak comfortably.
  4. Result: 3S 3300 mAh 25C, which stores 11.1 V × 3.3 Ah = 36.6 Wh. Charging at 1C means 3.3 A, about 1 h 12 min from empty, from a charger that can supply at least 12.6 V × 3.3 A ≈ 42 W.

For comparison, a 3S 2200 mAh pack would last only about 7 minutes at the same load, and a 5000 mAh pack about 16 minutes, but it weighs roughly twice as much as the 2200.

The weight trade-off

Capacity costs weight, and in anything that flies or accelerates, extra weight needs extra current, which eats into the run time you were buying. Doubling capacity rarely doubles run time on a drone. If the next size up adds a lot of weight for little gain, a second pack swapped between runs is usually the better buy.

Safety in four lines

  • Charge at 1C unless the label allows more, always with the balance lead, on a fireproof surface, never unattended.
  • Stop using a pack at about 3.3 V per cell under load (9.9 V for 3S); set the ESC's low-voltage cutoff accordingly.
  • Store at 3.8 V per cell (11.4 V for 3S) if it won't be used for a few days.
  • Retire any pack that is puffy, dented or gets hot during normal use.

For air travel, packs up to 100 Wh are generally allowed in carry-on bags only; a 4S 5000 mAh pack is 74 Wh, a 6S 5000 mAh pack 111 Wh and needs the airline's approval.

Work out your own pack

The LiPo calculator gives the voltages, energy, continuous and burst current, charge time and run time for any cell count, capacity and C rating, and warns when your load is above what the pack is rated for. For other battery types, the battery run time calculator estimates run time from capacity and load.

For a related walkthrough, read Drone Flight Time Calculation, Step by Step.

Looking for other tools?

Explore ToolSphere Homepage →