Picking a drive motor comes down to two numbers: the wheel speed that gives your top speed, and the torque to get there. Speed is easy. Torque depends on how fast you accelerate, what slope you climb and what you drive on, and it's the number people underestimate.
Wheel RPM from top speed
wheel RPM = speed (m/s) × 60 ÷ (π × wheel diameter in m)
For 1.2 m/s on 8 cm wheels: 1.2 × 60 ÷ (π × 0.08) = 286.5 RPM. That's at the wheel; with a gearbox, the motor spins faster by the gear ratio.
The three forces
The wheels have to push with enough force for all of these at once:
acceleration: F_a = m × a (a = top speed ÷ time to reach it)
slope: F_g = m × g × sin(θ)
rolling resistance: F_r = Crr × m × g × cos(θ)
Share the total between the driven wheels, multiply by the wheel radius for torque, and divide by the gearbox efficiency:
torque per motor = (F_a + F_g + F_r) ÷ motors × radius ÷ efficiency
Crr, the rolling resistance coefficient, depends on the wheel and the floor: about 0.015 for rubber on concrete, 0.05 on carpet and 0.1 on grass.
Worked example
A 5 kg robot, 2 driven wheels of 8 cm, reaching 1.2 m/s in 0.5 s on concrete, 85% efficient gearbox:
a = 1.2 ÷ 0.5 = 2.4 m/s²
F_a = 5 × 2.4 = 12.00 N
F_r = 0.015 × 5 × 9.81 = 0.74 N
per motor = 12.74 ÷ 2 = 6.37 N
torque = 6.37 × 0.04 ÷ 0.85 = 0.300 N·m
That's 3.06 kg·cm or 42.4 oz·in per motor at 286.5 RPM at the wheel.
What changes the answer
Same robot, one thing changed at a time:
| Change | Torque per motor | kg·cm | Wheel RPM |
|---|---|---|---|
| Baseline (above) | 0.300 N·m | 3.06 | 286.5 |
| On carpet (Crr 0.05) | 0.340 N·m | 3.47 | 286.5 |
| Up a 10° ramp | 0.500 N·m | 5.10 | 286.5 |
| Accelerating over 2 s, not 0.5 s | 0.088 N·m | 0.90 | 286.5 |
| 12 cm wheels | 0.449 N·m | 4.58 | 191.0 |
| 4 cm wheels | 0.150 N·m | 1.53 | 573.0 |
Two lessons stand out:
- Acceleration dominates on flat ground. Asking for top speed in half a second needs more than three times the torque of taking two seconds. If your motor is marginal, soften the acceleration in software first.
- Wheel size trades torque for speed. Bigger wheels need more torque and fewer RPM; the power stays the same. Choose the wheel for the terrain, then gear the motor to suit.
A heavier outdoor robot
20 kg, 4 driven 15 cm wheels, 1 m/s in 1 s, on grass (Crr 0.1):
| Terrain | Torque per motor | kg·cm | Wheel RPM |
|---|---|---|---|
| Flat grass | 0.874 N·m | 8.91 | 127.3 |
| 15° grassy slope | 1.979 N·m | 20.18 | 127.3 |
On the flat, rolling resistance on grass (19.6 N) is almost as big as the acceleration force (20 N). On the slope, gravity (50.8 N) dwarfs both. Size for the worst slope the robot must start on, not the average.
Turning torque into a motor choice
- Add margin. Motors are rated at stall and at their efficient running point; pick one whose rated (continuous) torque covers your number, with 30–50% to spare. Stall torque is not a continuous rating.
- Match RPM through the gearbox. If the motor's rated speed is 6,000 RPM and you need 286.5 at the wheel, a ratio of about 21:1 fits; the gearbox multiplies torque by the same ratio (less its losses).
- Check the current. The torque you need sets the current the motor draws, and that sizes the motor driver and its heat.
Common mistakes
- Using diameter instead of radius in torque = force × radius: a 2× error.
- Forgetting rolling resistance on carpet or grass.
- Sizing for constant speed only. Holding speed on the flat takes very little torque; accelerating and climbing take the rest.
- Mixing units. 1 N·m = 10.2 kg·cm = 141.6 oz·in. Hobby motors are rated in kg·cm, US datasheets often in oz·in.
Try it
The robot speed and torque calculator does all of this from mass, wheel size, speed, acceleration time, slope, efficiency and rolling resistance, in N·m, kg·cm and oz·in. Then check the driver's heat with the H-bridge power calculator and the H-bridge guide.