ToolSphere
Back to all articles
electronics

Series-Parallel Circuits Solved Step by Step

2026-10-157 min read

Try it: free Series/Parallel Equivalence Calculator

Combine resistors, capacitors or inductors in series or parallel

Open →

A series-parallel (or combination) circuit mixes both kinds of connection, so neither the series rule nor the parallel rule works on its own. The method is always the same two passes: collapse the circuit into one equivalent resistor to find the total current, then expand it again to find what each resistor sees. Here is the method, then a complete example with every number.

The rules you need

  • Series (one path, same current through each): R = R₁ + R₂ + …, and the voltages add up to the total.
  • Parallel (same two nodes, same voltage across each): 1/R = 1/R₁ + 1/R₂ + …, or R₁R₂ ÷ (R₁ + R₂) for two, and the currents add up to the total.
  • Ohm's law on any single resistor or group: V = I × R.

Two resistors are in series only if nothing else connects at the point between them. Two resistors are in parallel only if both of their ends connect to the same two nodes.

Pass 1: collapse to one resistor

Find the innermost group that is purely series or purely parallel, replace it with its equivalent, redraw, and repeat until one resistor is left.

Pass 2: expand back out

Use Ohm's law on the total to get the source current, then step back through each simplification in reverse. A series group shares a current, so multiply to get its voltages; a parallel group shares a voltage, so divide to get its currents.

Worked example

A 12 V battery drives R₁ = 100 Ω in series with a parallel pair: R₂ = 220 Ω on one branch, and R₃ = 330 Ω in series with R₄ = 470 Ω on the other.

        R1 = 100 Ω
 +12V ──/\/\/──┬──────────┬
               │          │
           R2 = 220 Ω  R3 = 330 Ω
               │          │
               │       R4 = 470 Ω
               │          │
   0V ─────────┴──────────┘

Collapse

  1. R₃ and R₄ are in series (nothing else joins between them): R₃₄ = 330 + 470 = 800 Ω.
  2. R₂ and R₃₄ connect across the same two nodes, so they are in parallel: R₂₃₄ = (220 × 800) ÷ (220 + 800) = 176,000 ÷ 1,020 = 172.55 Ω.
  3. R₁ is in series with that: R_total = 100 + 172.55 = 272.55 Ω.

Expand

  1. Total current from the battery: I = 12 ÷ 272.55 = 44.03 mA. All of it flows through R₁.
  2. Voltage across R₁: 0.04403 × 100 = 4.40 V. That leaves 12 − 4.40 = 7.60 V across the parallel section.
  3. Current through R₂: 7.60 ÷ 220 = 34.53 mA.
  4. Current through the R₃–R₄ branch: 7.60 ÷ 800 = 9.50 mA.
  5. Voltages in that branch: V₃ = 0.0095 × 330 = 3.13 V, V₄ = 0.0095 × 470 = 4.46 V.

Check

  • Currents at the junction: 34.53 + 9.50 = 44.03 mA, equal to the total. ✓
  • Voltages around the right-hand loop: 4.40 + 3.13 + 4.46 = 12.0 V. ✓
  • Power: R₁ 194 mW, R₂ 262 mW, R₃ 30 mW, R₄ 42 mW, total 528 mW = 12 V × 44.03 mA. ✓
Resistor Current Voltage Power
R₁ 100 Ω 44.03 mA 4.40 V 194 mW
R₂ 220 Ω 34.53 mA 7.60 V 262 mW
R₃ 330 Ω 9.50 mA 3.13 V 30 mW
R₄ 470 Ω 9.50 mA 4.46 V 42 mW

Note that R₂ dissipates 262 mW, more than a common ¼ W (250 mW) resistor is rated for. Checking power is the step most homework skips and most real circuits need.

Common mistakes

  • Calling two resistors "in series" because they are drawn in a line. If a third branch connects between them, they are not.
  • Using the total voltage across a parallel group. In the example only 7.60 V reaches R₂, not 12 V, because R₁ drops 4.40 V first.
  • Rounding too early. Keep at least four significant figures until the end, or the checks above won't add up.
  • Adding parallel resistances. A parallel result is always smaller than its smallest branch (172.55 Ω < 220 Ω); if yours is bigger, the formula was applied the wrong way round.

Check your answer

In the series and parallel calculator, type the network as an expression, 100 + 220 || (330 + 470) (+ for series, || for parallel), to get 272.5 Ω, or enter a group's values with a supply voltage to see the voltage, current and power in each resistor. For a single voltage divider, the voltage divider calculator gives the output directly.

For a related walkthrough, read Resistor Color Code: Chart and Examples.

Looking for other tools?

Explore ToolSphere Homepage →