Small ceramic and film capacitors don't have room for "0.1 µF", so they carry a short code instead. The rule is the same one resistor color bands use, just written in digits.
Three-digit codes
The first two digits are the value; the third says how many zeros to add. The result is in picofarads.
104 → 10 followed by 4 zeros → 100,000 pF = 100 nF = 0.1 µF
| Code | Picofarads | Nanofarads | Microfarads |
|---|---|---|---|
| 101 | 100 pF | 0.1 nF | 0.0001 µF |
| 221 | 220 pF | 0.22 nF | 0.00022 µF |
| 102 | 1,000 pF | 1 nF | 0.001 µF |
| 222 | 2,200 pF | 2.2 nF | 0.0022 µF |
| 472 | 4,700 pF | 4.7 nF | 0.0047 µF |
| 103 | 10,000 pF | 10 nF | 0.01 µF |
| 223 | 22,000 pF | 22 nF | 0.022 µF |
| 473 | 47,000 pF | 47 nF | 0.047 µF |
| 104 | 100,000 pF | 100 nF | 0.1 µF |
| 224 | 220,000 pF | 220 nF | 0.22 µF |
| 474 | 470,000 pF | 470 nF | 0.47 µF |
| 105 | 1,000,000 pF | 1,000 nF | 1 µF |
| 106 | 10 µF | ||
| 476 | 47 µF | ||
| 107 | 100 µF |
104 is the one to remember: it's the 0.1 µF decoupling capacitor that sits next to almost every chip.
106, 476 and 107 are technically outside the EIA standard, which leaves multipliers 6 and 7 unused, but you'll see them all the time on tantalum and large ceramic capacitors.
Small values
- A third digit of 9 means ×0.1 and 8 means ×0.01: 479 is 4.7 pF, 109 is 1 pF.
- A third digit of 0 adds no zeros: 220 is 22 pF, not 220.
- Two digits alone are already picofarads: 47 is 47 pF.
- R is a decimal point in picofarads: 4R7 is 4.7 pF.
The tolerance letter
A letter straight after the code gives the tolerance:
| Letter | Tolerance |
|---|---|
| B | ±0.1 pF |
| C | ±0.25 pF |
| D | ±0.5 pF |
| F | ±1% |
| G | ±2% |
| J | ±5% |
| K | ±10% |
| M | ±20% |
| Z | +80% / −20% |
So 104K is 100 nF ±10%, and 473J is 47 nF ±5%. Z is common on cheap ceramic decoupling capacitors, where the exact value hardly matters.
The voltage prefix
Film capacitors often add a two-character voltage code in front: 2A104J is 100 V, 100 nF, ±5%.
| Code | Voltage | Code | Voltage | |
|---|---|---|---|---|
| 0J | 6.3 V | 2A | 100 V | |
| 1A | 10 V | 2D | 200 V | |
| 1C | 16 V | 2E | 250 V | |
| 1E | 25 V | 2G | 400 V | |
| 1V | 35 V | 2W | 450 V | |
| 1H | 50 V | 2J | 630 V |
Never use a capacitor above its rated voltage, and leave a margin: a part rated 50 V is the usual choice on a 24 V rail.
Letter-as-decimal markings
Some film capacitors and schematics write the unit letter where the decimal point goes:
| Marking | Value |
|---|---|
| p47 | 0.47 pF |
| 4p7 | 4.7 pF |
| 1n0 | 1 nF |
| 4n7 | 4.7 nF |
| 100n | 100 nF (same as 104) |
| 2u2 | 2.2 µF |
Common mistakes
- Reading the code as nanofarads or microfarads. The three-digit code is always in pF; convert afterwards.
- Reading 220 as 220 pF. The 0 is a multiplier, so it's 22 pF.
- Ignoring Z tolerance in a timing circuit. A Z-rated 104 can be anywhere from 80 nF to 180 nF. Use a C0G or film part when the value matters.
- Mistaking the voltage code for the value. In 2A104J, only 104 is the capacitance.
Try it
The capacitor code decoder reads any of these markings, including 104K, 2A104J and 4n7, and gives the value in pF, nF and µF with the tolerance and voltage. Once you have the value, the RC filter calculator uses it, and the resistor color code guide covers the resistor beside it.