ToolSphere
Back to all articles
electronics

Resistor Color Code: Chart and Examples

2026-10-206 min read

Try it: free Resistor Color Code Decoder

Pick resistor band colors to read resistance and tolerance

Open →

Through-hole resistors are too small to print a number on, so their value is painted on as colored bands. Once you know the chart, reading one takes a few seconds.

The chart

Color Digit Multiplier Tolerance
Black 0 × 1
Brown 1 × 10 ±1%
Red 2 × 100 ±2%
Orange 3 × 1 k
Yellow 4 × 10 k
Green 5 × 100 k ±0.5%
Blue 6 × 1 M ±0.25%
Violet 7 × 10 M ±0.1%
Grey 8 × 100 M
White 9 × 1 G
Gold × 0.1 ±5%
Silver × 0.01 ±10%
(no band) ±20%

The digits run black to white in rainbow order: black, brown, red, orange, yellow, green, blue, violet, grey, white. A common memory aid is "BB ROY of Great Britain has a Very Good Wife".

Which end do you start from?

  • The tolerance band (usually gold or silver on 4-band parts, brown on 5-band ones) goes on the right.
  • It is often set slightly apart from the others, or the first band is closer to the end of the body.
  • Gold and silver are never the first band. If you see one at an end, that end is the right-hand side.

Reading a 4-band resistor

Bands 1 and 2 are digits, band 3 is the multiplier, band 4 is the tolerance.

Bands Digits × Multiplier Value
red, red, brown, gold 2 2 × 10 220 Ω ±5%
brown, black, red, gold 1 0 × 100 1 kΩ ±5%
brown, black, orange, gold 1 0 × 1 k 10 kΩ ±5%
yellow, violet, orange, gold 4 7 × 1 k 47 kΩ ±5%
brown, black, yellow, gold 1 0 × 10 k 100 kΩ ±5%
orange, orange, gold, gold 3 3 × 0.1 3.3 Ω ±5%

A quick shortcut: the multiplier color tells you how many zeros to write after the two digits. Brown, black, red is 1, 0 and two zeros: 1,000 Ω.

Reading a 5-band resistor

Precision (1% and better) resistors use three digits, so bands 1–3 are digits, band 4 is the multiplier and band 5 the tolerance.

Bands Digits × Multiplier Value
brown, black, black, brown, brown 1 0 0 × 10 1 kΩ ±1%
orange, orange, black, black, brown 3 3 0 × 1 330 Ω ±1%
brown, black, black, red, brown 1 0 0 × 100 10 kΩ ±1%
yellow, violet, black, red, brown 4 7 0 × 100 47 kΩ ±1%

Notice that 1 kΩ is brown, black, red on a 4-band part but brown, black, black, brown on a 5-band one. Same resistor, different code, which is why counting the bands first matters.

6-band resistors

A 6-band resistor reads exactly like a 5-band one, plus a final band for the temperature coefficient: how much the value drifts per degree, in parts per million per kelvin. Brown is 100 ppm/K, red 50, orange 15, yellow 25, blue 10. You rarely need it outside precision measurement work.

What tolerance means in practice

A 1 kΩ ±5% resistor can measure anywhere from 950 Ω to 1,050 Ω and still be in spec. That is why resistor values come in the E-series (E12: 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82): the steps are spaced so that neighbouring values' tolerance ranges just about touch. If you measure 4.6 kΩ on a part that should be 4.7 kΩ ±5%, it is fine.

Common mistakes

  • Reading from the wrong end. 1 kΩ read backwards (gold, red, black, brown) makes no sense, which is your clue. But some reversed codes are valid values, so look for the tolerance band.
  • Confusing brown, red and orange, especially under warm light. Check with a multimeter if it matters.
  • Mixing up 4-band and 5-band rules. Count the bands before decoding.
  • Reading violet as blue or grey as white. Again, a meter settles it.

Try it

The resistor color code decoder lets you click the bands on a drawing of a 4, 5 or 6-band resistor and shows the value, the tolerance range and the nearest E12 and E24 values. Once you know the value, the LED resistor calculator, Ohm's law calculator and series and parallel calculator take it from there.

For a related walkthrough, read Series-Parallel Circuits Solved Step by Step.

Looking for other tools?

Explore ToolSphere Homepage →