Trace width is set by current, not voltage. Voltage decides how far apart traces must be (clearance); current decides how wide each one must be so it doesn't overheat or drop too much voltage. The easiest way to see how this works is to size every trace on one real board. Here is a small motor-driver board: a 12 V supply, a DC motor that draws 3 A continuously, and logic signals from an Arduino.
Step 1: signal traces are set by the factory, not the current
An Arduino pin driving a MOSFET gate or an LED carries 20 mA at most. By the IPC-2221 formula, 20 mA on 1 oz copper needs a trace less than 0.1 mil wide, far narrower than any factory can make. So signal traces are sized by what the board house can etch reliably:
- Most low-cost fabs handle 0.15 mm (6 mil) traces on standard boards.
- 0.25 mm (10 mil) is a comfortable default for signals: easy to make, easy to repair, and still dense enough for most hobby boards.
Step 2: the power trace, by IPC-2221
The 3 A motor current is the trace that matters. On an outer layer with 1 oz copper and a 10 °C allowed rise:
A = (I ÷ (0.048 × ΔT^0.44))^(1/0.725)
= (3 ÷ (0.048 × 10^0.44))^1.379 = 74.2 mil²
width = A ÷ thickness = 74.2 ÷ 1.378 = 53.8 mil = 1.37 mm
Round up to something your design tool and eye like: 1.5 mm or, if there is room, 2 mm. Two levers if space is tight:
| Change | Width for 3 A |
|---|---|
| 1 oz copper, 10 °C rise | 1.37 mm |
| 1 oz copper, 20 °C rise | 0.90 mm |
| 2 oz copper, 10 °C rise | 0.68 mm |
A 20 °C rise is usually fine for a power trace on a board that isn't inside a hot enclosure. 2 oz copper costs a little more at the board house but halves every power-trace width.
Step 3: check the voltage drop
A wide-enough trace can still waste voltage. With a 60 mm run from the input connector to the driver chip:
| Width | Resistance (60 mm, at 35 °C) | Drop at 3 A | Heat |
|---|---|---|---|
| 1.4 mm | 22.4 mΩ | 67 mV | 0.20 W |
| 2.0 mm | 15.6 mΩ | 47 mV | 0.14 W |
On a 12 V supply, 47 mV is 0.4% and doesn't matter. The same drop on a 3.3 V rail would be 1.4%, and on a long trace feeding a sensor's reference it can matter a lot. Low-voltage, high-current rails are where you go wider than the thermal minimum.
Step 4: don't forget the return path
Every amp that goes out on the 12 V trace comes back on ground. A thin ground trace undoes the work above. Use a ground pour (a copper fill on the bottom layer) so the return current has a wide, short path, and keep the motor's return away from the Arduino's analog ground where you can.
Step 5: vias carry less than you think
If the power trace changes layers, the vias have to carry the full 3 A. A typical 0.3 mm via has a plated barrel about 25 µm (1 mil) thick, which is a cross-section of roughly 37 mil². Treated as an inner-layer conductor in the IPC-2221 formula, that is about 0.9 A for a 10 °C rise. So:
- Use at least four 0.3 mm vias side by side for 3 A, or larger vias.
- Better still, keep high-current paths on one layer and avoid vias in them entirely.
Step 6: clearance is a separate question
Width handles current; spacing handles voltage. At 12 V, the default 0.2 mm (8 mil) clearance most design tools use is plenty. Anything near mains voltage needs much larger gaps, slots and creepage distances from the IPC-2221 clearance tables or the relevant safety standard. Don't use a trace-width calculator to decide that.
The finished board
| Net | Width | Why |
|---|---|---|
| Arduino signals | 0.25 mm | Manufacturing comfort; current is tiny |
| 12 V motor supply | 2.0 mm (1.4 mm minimum) | 3 A at a 10 °C rise, low drop |
| Ground | Pour on the bottom layer | Return current and noise |
| Layer changes on 12 V | 4 × 0.3 mm vias | About 0.9 A each |
Common mistakes
- Sizing every trace for the biggest current. Wide signal traces waste space and make routing harder; only power nets need it.
- Using the inner-layer number for an outer trace, or the reverse. IPC-2221 asks for about 2.6 times the copper on inner layers.
- Forgetting that the rise adds to ambient. A 20 °C rise inside a 50 °C enclosure means a 70 °C trace.
- One via on a power net. It becomes the hottest point on the board.
Try it
The PCB trace width calculator does steps 2 and 3 for any current, copper weight and layer, and tells you how much current an existing trace can carry. For the wiring off the board, the AWG wire gauge calculator gives wire sizes, and the thermal resistance calculator checks whether the driver chip itself needs a heatsink.
For a related walkthrough, read Series-Parallel Circuits Solved Step by Step.