An inductor and a capacitor together form a resonant (or "tank") circuit. Energy sloshes back and forth between the capacitor's electric field and the inductor's magnetic field at one natural frequency. That frequency is what tunes a radio, sets an oscillator, and picks one channel out of many.
f = 1 / (2π · √(L · C))
with L in henries, C in farads and f in hertz.
A worked example
L = 10 µH, C = 100 pF:
L · C = 10 × 10⁻⁶ × 100 × 10⁻¹² = 1 × 10⁻¹⁵
√(L·C) = 3.162 × 10⁻⁸
f = 1 / (2π × 3.162 × 10⁻⁸) = 5.033 MHz
| L | C | Resonant frequency |
|---|---|---|
| 10 µH | 100 pF | 5.033 MHz |
| 1 µH | 1 nF | 5.033 MHz |
| 1 µH | 100 pF | 15.915 MHz |
| 4.7 µH | 100 pF | 7.341 MHz |
| 100 µH | 253.3 pF | 1.000 MHz |
| 0.1 µH | 25 pF | 100.658 MHz |
As with RC filters, only the product L·C sets the frequency, which is why the first two rows match. And because of the square root, you need to change L·C by 4× to halve or double the frequency.
Why it resonates: the reactances cancel
An inductor's reactance rises with frequency (X_L = 2πfL); a capacitor's falls (X_C = 1/(2πfC)). Resonance is the one frequency where they're equal and opposite. For 10 µH and 100 pF at 5.033 MHz, both are 316.2 Ω.
- In a series LC, they cancel, the impedance drops to just the wire resistance, and current peaks. Good for passing one frequency.
- In a parallel LC, the impedance peaks instead. Good for selecting one frequency and rejecting the rest, as in an oscillator or radio front end.
Example: tuning an AM radio
AM broadcast runs from about 530 kHz to 1,700 kHz. A classic crystal-set or transistor radio uses a fixed 250 µH coil and a variable capacitor:
| Capacitor setting | Resonant frequency |
|---|---|
| 365 pF (fully meshed) | 527 kHz |
| 40 pF (nearly open) | 1,592 kHz |
A 365 pF variable capacitor covers the whole band with one coil. The capacitance changes by about 9×, and the frequency by √9 = 3×, close to the 3.2× ratio between the edges of the band.
Example: choosing L for a target frequency
Rearrange the formula:
L = 1 / ((2π · f)² · C)
For the 10.7 MHz IF used in FM receivers, with a 100 pF capacitor, L = 2.21 µH. The nearest standard value is 2.2 µH, which resonates at 10.73 MHz; a trimmer capacitor or adjustable coil takes up the last 0.3%.
Why real circuits come out a bit off
- Stray capacitance. PCB traces, the transistor's own capacitance and the coil's turn-to-turn capacitance add a few pF. At 100 MHz with 25 pF that's a big fraction.
- Component tolerance. A ±10% capacitor alone moves the frequency by about ±5%.
- Resistance. Losses don't move the frequency much but widen the peak (lower the Q).
That's why tuned circuits nearly always include something adjustable.
Common mistakes
- Leaving out the square root. Without it the answer is off by orders of magnitude.
- Unit slips. µH and pF are 10⁻⁶ and 10⁻¹²; mixing up nF and pF gives a frequency 31.6× wrong (√1000).
- Using 1/√(LC) for hertz. That's the angular frequency ω in rad/s; divide by 2π.
Try it
The LC resonant frequency calculator takes L in µH and C in pF and gives the frequency in MHz. If your capacitor only says "101" or "4n7", the capacitor code decoder gives its value; for the resistor-capacitor version of the same idea, see the RC filter guide.