ToolSphere
Back to all articles
electronics

Decibels Explained: dB, dBm and Ratios

2026-10-206 min read

Try it: free Decibel (dB) Converter

Convert power and voltage ratios to decibels and back

Open →

A decibel is a ratio on a logarithmic scale. That's all. It turns huge ranges (a radio receiver handles signals a trillion times weaker than its transmitter) into manageable numbers, and it turns multiplication into addition, which is why engineers use it everywhere from audio to RF.

Two formulas, and why

power ratio:   dB = 10 · log10(P2 / P1)
voltage ratio: dB = 20 · log10(V2 / V1)

Power is proportional to voltage squared (P = V²/R), and log(x²) = 2·log(x). So the factor of 20 for voltage is just the 10 for power, doubled. The same 20 applies to current and sound pressure; the 10 to anything measured as power or energy.

The upshot: the same circuit has the same gain in dB whichever you measure. Doubling the voltage into a fixed load quadruples the power, and both come out as +6 dB.

The table worth memorising

dB Power ratio Voltage ratio
+60 1,000,000 1,000
+40 10,000 100
+20 100 10
+10 10 3.162
+6 3.981 (≈ 4) 1.995 (≈ 2)
+3 1.995 (≈ 2) 1.413
+1 1.259 1.122
0 1 1
−3 0.501 (half) 0.708
−6 0.251 (quarter) 0.501 (half)
−20 0.01 0.1

Three rules of thumb cover most of it:

  • 3 dB is double the power. −3 dB is half, which is why a filter's cutoff is the "−3 dB point".
  • 6 dB is double the voltage.
  • Every 10 dB is ×10 in power; every 20 dB is ×10 in voltage.

dB is relative; dBm is absolute

Plain dB compares two things. Add a reference and it becomes an absolute level:

Unit Reference Used for
dBm 1 milliwatt RF power, Wi-Fi, fibre optics
dBW 1 watt transmitters
dBV 1 volt RMS consumer audio
dBu 0.775 V RMS pro audio
dB SPL 20 µPa loudness

dBm is the one you'll meet most. Convert with mW = 10^(dBm/10):

dBm Power Typical
50 100 W broadcast transmitter
40 10 W
33 2 W handheld radio
30 1 W
27 501 mW
20 100 mW Wi-Fi router limit (2.4 GHz, many regions)
10 10 mW
0 1 mW
−30 1 µW
−70 0.1 nW weak but usable Wi-Fi signal
−90 1 pW near a receiver's noise floor

Notice 0 dBm is not zero power; it's 1 mW. Negative dBm just means less than a milliwatt.

Adding up a signal chain

Because decibels are logarithms, you add gains and losses instead of multiplying ratios. A −40 dBm signal goes through a 20 dB amplifier, 3 dB of cable loss and a filter that costs 1 dB:

−40 + 20 − 3 − 1 = −24 dBm  →  0.00398 mW (about 4 µW)

Doing the same with ratios (× 100 × 0.501 × 0.794) gets you the same answer much more slowly. You can add dB to dBm (a gain applied to a level), but adding two dBm levels is wrong: two 0 dBm signals combine to 2 mW, which is +3.01 dBm, not 0 dBm.

Common mistakes

  • Using 10·log on a voltage ratio. A ×2 voltage gain is 6.02 dB, not 3.01.
  • Taking the log of a negative or zero ratio. There's no such dB value. A signal that inverts (×−2) still has a gain of 6.02 dB; the sign is phase, not magnitude.
  • Adding dBm to dBm. Convert to milliwatts, add, and convert back.
  • Thinking −3 dB means a 3% drop. It's about 29% of the voltage, and half the power.

Try it

The decibel converter converts both ways for voltage and power ratios and, in power mode, turns dBm into milliwatts. To see dB in action across frequency, plot a filter with the Bode plot generator, or start with the RC filter cutoff guide.

Looking for other tools?

Explore ToolSphere Homepage →