ToolSphere

Drywall Calculator

Home projects

Estimate drywall sheets from wall and ceiling area, openings and waste. Compare sheet sizes, with stated screw and joint compound shopping allowances.

Sheets to buy

15 sheets · 4 × 8 ft

430 sq ft net (39.95 m²) · 473 sq ft with waste

About 480 screws · 4.45 US gal compound

1 × 4.5 US gal pails. Shopping allowances; check sheet layout and product instructions.

Total area of all wall faces before subtracting openings. Maximum 10,000,000 sq ft.

Enter 0 if you are covering walls only. Maximum 10,000,000 sq ft.

Combined doors, windows and other uncovered areas; cannot exceed gross area. Maximum 10,000,000 sq ft.

Enter 0–100. Applies to net area before sheets and compound are estimated.

Sheets = round up [(walls + ceiling − openings) × (1 + waste %) ÷ sheet area]. Combined area assumes cuts can be reused; this is not a sheet layout.

Screws: one per square foot of purchased sheets, a rough shopping allowance only. Fastener spacing, length and type must follow the board manufacturer and your assembly requirements.

Compound: 9.4 US gal per 1,000 sq ft of waste-adjusted area; round up to 4.5 US gal pails. This uses USG midweight ready-mix coverage (checked November 12, 2026). Other products and finishes differ; skim coating, texture and major repairs need separate estimates.

Sheet thickness, framing, fire ratings, moisture suitability, tape, corner bead and installation labor are outside this estimate.

On this browser only

Give feedback

Did this tool help?

Tell us what worked, what didn’t, or what you’d like next.

Opens Google Forms in a new tab with this tool’s name filled in. No sign-in or email required. Feedback is optional.

How to use Drywall Calculator

  1. 1Enter total wall and ceiling areas in square feet, using zero for unused surfaces.
  2. 2Subtract the combined uncovered area of openings.
  3. 3Choose 4 × 8 ft or 4 × 12 ft sheets and set waste.
  4. 4Read the sheet count and supply allowances; confirm a layout and product instructions.

About Drywall Calculator

Estimate drywall sheets and finishing supplies

Use this drywall calculator to plan a material order for walls, ceilings or both. Enter the total wall area and ceiling area in square feet, subtract the combined area of uncovered openings, select a sheet size and set a waste allowance. The answer appears above the form with whole sheets, a rough screw quantity and an estimate of ready-mixed joint compound. Square meters appear alongside the net area for reference. All calculations run in your browser.

Measure each wall face separately and add the areas before entering the wall total. Include only the faces that will receive board. For ceilings, measure the actual surface rather than assuming the floor footprint is accurate for every shape. Sloped ceilings and soffits need their own measurements. The calculator accepts combined areas; it does not infer wall area from floor area or generate a room drawing. Use the area converter if your measurements came from a metric plan.

Subtract openings carefully

The openings field represents the total uncovered area across the walls and ceiling you entered. Doors, windows and access openings can reduce net coverage, but the way you cut around them may still consume substantial board. Enter the area you want to subtract rather than counting every opening automatically. If a small opening will be cut from the middle of a sheet, treating its area as reusable material can make an area-only estimate optimistic.

The calculator rejects an opening total larger than the combined wall and ceiling area. Zero is valid for any individual area field. If openings equal the gross area, the remaining coverage and material quantities are zero. Blank fields are not silently treated as zero; enter zero explicitly where it applies. This makes a missing measurement easier to spot before it turns into a shopping list.

Worked example: walls and ceiling

The loaded example has 352 sq ft of walls and 120 sq ft of ceiling, with 42 sq ft of openings. Running the calculation library gives 430 sq ft of net board coverage, or about 39.95 m². A 10% waste allowance raises the planning area to 473 sq ft. With 4-by-8-foot sheets, the tool divides by 32 sq ft per sheet and rounds up to 15 sheets, providing 480 sq ft of purchased board.

The screw shopping allowance is therefore 480 screws. The joint compound estimate is 4.4462 US gallons, displayed as 4.45 US gal, which rounds up to one 4.5-US-gallon pail. Selecting 4-by-12-foot sheets for the same example changes the order to ten sheets. Purchased board area remains 480 sq ft, so the screw allowance stays the same. The compound estimate also stays the same because it uses waste-adjusted area rather than whole-sheet purchasing area.

Compare sheet sizes with a layout

Both sheet sizes are four feet wide. A longer sheet can reduce some seams, but it may be harder to carry, position or fit through access routes. The calculator only compares areas; it cannot establish the best sheet orientation or whether cuts from one surface can be reused on another. Wall height, ceiling spans, framing locations and joint placement all affect the actual sheet order. Check those details on a layout before purchasing.

Waste is added to net coverage before sheets are rounded up. It represents a planning allowance for cuts and losses, while whole-sheet rounding may add further surplus. The tool combines walls and ceilings into one order, assuming the same sheet size and that material can be shared between surfaces. If the ceiling requires a different board product or thickness, run separate estimates and keep the quantities separate. Multiple layers must also be planned separately.

Read the supply rules as allowances

Screws use an explicit shopping rule: one screw per square foot of purchased board. This is a rough quantity allowance, not a fastening schedule. It does not specify screw spacing, length, coating or suitability for wood or steel framing. Follow the board manufacturer's installation instructions and the requirements for your actual wall or ceiling assembly. Buy suitable package quantities after checking those instructions; the calculator does not convert screws into pounds or boxes.

Joint compound uses 9.4 US gallons per 1,000 sq ft of waste-adjusted area, based on the published coverage for USG midweight ready-mix compound, checked November 12, 2026. The result rounds up to 4.5-US-gallon pails. Actual consumption depends on the selected product, joint layout, application and finish. Full skim coating, texture and major repairs need separate allowances. Use your product's instructions when they differ.

Finish the project budget separately

This estimate does not select board thickness, moisture resistance, fire rating or framing. It excludes tape, corner bead, adhesive, primer, paint, delivery and labor. It also does not verify building-code compliance or determine whether existing surfaces are suitable. After confirming the sheet layout and finishing products, use the paint calculator to plan the later coating stage. Keep board, finishing and painting purchases as separate budget items.

Frequently asked questions

How do I calculate wall area?

Measure each wall face, multiply its length by its height and add the areas. Enter ceiling area separately.

Can I subtract doors and windows?

Yes. Enter their combined uncovered area in the openings field. Small cutouts may not save usable board, so review the layout.

Which sheet sizes are supported?

Choose four-foot-wide sheets with an eight- or twelve-foot length. The calculator compares area, not seam or framing layouts.

How is waste applied?

The selected percentage increases net coverage after openings are subtracted. Sheet quantities are then rounded up.

How are screws estimated?

The shopping allowance is one screw per square foot of purchased board. It is not an installation spacing rule or a code requirement.

How is joint compound estimated?

The rule uses 9.4 US gallons per 1,000 square feet of waste-adjusted area and rounds up to 4.5-US-gallon pails, based on USG midweight ready-mix coverage.

Does compound include skim coating?

No. Product coverage varies, and full skim coating, texture and major repairs need a separate estimate.

Can walls and ceilings use different board?

Run separate estimates when sizes, thicknesses or products differ. This calculation combines the entered surfaces into one sheet order.

Does the calculator choose drywall thickness?

No. Check framing, assembly requirements, fire rating, moisture exposure and manufacturer instructions before selecting board and fasteners.

What if my net area is zero?

The tool returns zero sheets, screws and compound. Missing measurements must be entered explicitly; blank fields clear the estimate.

Have a suggestion for Drywall Calculator?Share your feedback ↗