Estimate concrete before a DIY pour
Use this concrete calculator to turn the dimensions of a slab, rectangular footing, round column or solid staircase into a material quantity. The answer starts with cubic yards and cubic meters, including your chosen waste allowance. It also converts the same requirement into alternative orders of premixed concrete bags. Choose the bag you intend to buy rather than adding the different bag counts together.
The loaded example gives you a starting point without pressing Calculate. Replace the measurements with those from your project, then check the assumptions before ordering. This is a volume estimate: it does not choose a concrete strength, establish foundation dimensions, check loads or determine reinforcement. A quantity that fills the shape is not evidence that the design meets local requirements.
Measure the concrete shape
For a slab or rectangular footing, volume = length × width × depth. Use the actual concrete depth, excluding the gravel bed and other material below it. A footing input represents one rectangular strip, not an entire perimeter with overlapping corners. For a round column, volume = π × (diameter ÷ 2)² × height. Enter the full diameter, not the radius. The cylinder has no enlarged base or hollow center.
For steps, the model is a solid staircase standing on a level base. Every rise and tread depth is equal, and the width stays constant. Volume = width × rise × tread depth × number of steps × (number of steps + 1) ÷ 2. Each tread has concrete beneath it all the way to the level base. This does not model a thin sloping stair slab, filled steps, a separate landing or a hollow underside. Estimate those designs separately from their actual geometry.
Feet and inches come first, with editable meters alongside. Enter zero in an unused feet or inches field; a blank field clears the answer. Inches must be less than a foot, and the combined dimension must be positive. Changing either measurement system updates the other. Converted fields round for readability, while calculations retain the active entered value. The length converter can help you check other formats.
Worked example: a small rectangular slab
The example is calculated with this tool’s own library. A slab measuring 10 ft by 8 ft, with a depth of 4 in, contains about 26.667 ft³ or 0.755 m³ before waste. With the loaded 10% allowance, the requirement becomes about 29.333 ft³: 1.086 yd³ or 0.831 m³. The headline volume includes that allowance; it is not the bare geometric volume.
Using the stated US yields, this order needs 98 bags of 40 lb, 66 bags of 60 lb or 49 bags of 80 lb concrete mix. These are alternative purchases. At the example price of $6.50 for each 80 lb bag, the material total is $318.50. Using the UK default yields instead gives 84 bags of 20 kg or 70 bags of 25 kg. Different products can have different yields and intended uses, so weight alone is not enough to select a mix.
Waste and whole-bag rounding
The calculator multiplies measured volume by one plus waste percentage divided by 100. It then divides that requirement by each bag’s mixed yield and rounds up to a whole bag. Bag counts use unrounded volumes, so dividing the rounded headline by a yield may produce a slightly different intermediate figure. The quantity table distinguishes the measured volume from the volume with waste.
The example allowance is a comparison scenario, not a universal recommendation. Uneven excavation, irregular forms and losses during placing can affect the requirement. Measure carefully and agree an allowance with your supplier or installer. Increasing waste does not correct an incorrect thickness or an omitted section. For separate pours, check each shape and decide whether leftover mixed material can actually be shared before combining an order.
Match the bag to its published yield
US defaults use the approximate mixed yields in the QUIKRETE Concrete Mix data sheet. UK defaults use Blue Circle Multi-Purpose Concrete for the smaller bag and Natural Cement TRACKCRETE for the larger bag. Their exact yields and the source-check date appear beside the editable UK yield fields.
TRACKCRETE is a specialist repair product, not a recommendation for every slab or footing. Check the application as well as the volume. Replace a UK default with the mixed liters stated on your chosen bag. These estimates are for complete premixed concrete, not bags of cement that need separate sand and aggregate. Follow the product’s mixing instructions; adding extra water is not a way to obtain the calculated quantity.
Budget for the whole project
Optional cost multiplies the selected size’s whole-bag count by its entered price. USD and GBP label that price without converting currencies. Leave price blank for quantities alone. Delivery, taxes, labor, tools, forms, base preparation and reinforcement are separate costs. For a larger order, compare supplier delivery options using the cubic-yard or cubic-meter requirement and confirm order increments directly. Check measurements, product suitability and the final site plan before purchase.